Moa Red Dot

ADE RD3-019 STINGRAY Red Dot For Pistol with Trijicon RMR Footprint -6 MOA

ADE RD3-019 STINGRAY Red Dot For Pistol with Trijicon RMR Footprint -6 MOA
ADE RD3-019 STINGRAY Red Dot For Pistol with Trijicon RMR Footprint -6 MOA
ADE RD3-019 STINGRAY Red Dot For Pistol with Trijicon RMR Footprint -6 MOA
ADE RD3-019 STINGRAY Red Dot For Pistol with Trijicon RMR Footprint -6 MOA
ADE RD3-019 STINGRAY Red Dot For Pistol with Trijicon RMR Footprint -6 MOA
ADE RD3-019 STINGRAY Red Dot For Pistol with Trijicon RMR Footprint -6 MOA
ADE RD3-019 STINGRAY Red Dot For Pistol with Trijicon RMR Footprint -6 MOA
ADE RD3-019 STINGRAY Red Dot For Pistol with Trijicon RMR Footprint -6 MOA
ADE RD3-019 STINGRAY Red Dot For Pistol with Trijicon RMR Footprint -6 MOA
ADE RD3-019 STINGRAY Red Dot For Pistol with Trijicon RMR Footprint -6 MOA

ADE RD3-019 STINGRAY Red Dot For Pistol with Trijicon RMR Footprint -6 MOA

Ade Stingray is Designed to be the smallest and lightest red dot to fit any pistol mounting plate/slide/cut that is compatible with Trijicon RMR/SRO(both type 1 and type 2 RMR), Holosun 407C/507C/508T footprint red dots. The overall length is around 15-20% shorter than other major red dots on the market. The shorter design allow this sight to be able to sit in to all optic cuts/plates/adapters that are designed for RMR footprint. For some optics ready pistols with a larger optic cut, there might be a gap between the rear of the Stingray and pistol rear iron sight.

Ade Stingray created an iron sight curve at the end of the body, and also added two white dots on the curve. For the rear of part of the red dot to become a back up iron sight. With the ultra short design, the red dot provides a distance/gap on some full size optics ready pistol, to give enough distance to be a Co-Witness back up sight, in addition to the LED dot and pistol equipped iron sight. For non-optics ready pistols that need to use an optic plate/adapter to replace the pistol manufacture equipped rear sight, ADE Stingray's rear white dot will act as a pistol factory original rear sight for Co-Witness. For non-optics ready pistols that need to use an optic plate/adapter to replace the pistol manufacture equipped rear sight, ADE Stingray's rear white dot acts as a pistol factory original rear sight for Co-Witness.

The light turns brighter or lower automatically. If you do not use it, put the provided rubber cover on it, then the sight will be "sleeping" in a very very low power mode. Hard coated aircraft aluminum and multi-coated glass. Not plastic body with polymer lens. ADE Stingray RED dot sight is always powered on with automatic brightness.

H a single CR2032 3v battery. With our advanced technology the sight only draws approximate 700 microampere powers to give a very long battery life. The brightness will turn high and low accordingly to the environment brightness. (Length)1.6" x (Width)1.1" x (Height).

Comes with screws for several Optics Ready handguns. Does not comes with any mounting plate such as picatinny mount or plate made for a specific handgun. We always reply emails within 8 hours.

All NFA rules apply, where applicable. YOU are responsible to following ALL laws and regulations regarding the ownership, possession and end use of this item. This item is in the category "Sporting Goods\Hunting\Scopes, Optics & Lasers\Red Dot & Laser". The seller is "opticsfactory" and is located in this country: US. This item can be shipped to United States.

  • Model: RD3-019 STINGRAY
  • Reticle Color: Red
  • Type: Dot
  • MPN: RD3-019 STINGRAY
  • Brand: ade advanced optics

ADE RD3-019 STINGRAY Red Dot For Pistol with Trijicon RMR Footprint -6 MOA